What are your ideas regarding How to Install a Bathtub?
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Mounting a tub isn't exactly rocket science, however it does require solid plumbing, woodworking, as well as often, tiling abilities. Changing an old bath tub with a brand-new one is likewise a reasonably tough project. If the old tub is readily accessible, the project can relocate speedily; if you need to open up a wall surface to eliminate the old tub as well as position the new bath tub, the job is a lot harder. In either situation, the job is within a home handyman's skills, although you will certainly require an assistant to leave the old tub and embeded in the brand-new one. Ensure you have actually qualified yourself for the work as well as are comfortable trying it. Instead of hiring a specialist to take over a halfway-completed project, it is far better to think about using one before you start. Possibilities are you may require an expert plumber to make tube connections.
This post will aid you set up a new tub in your bathroom if you have actually already acquired a new bathtub as well as don't require to change the plan of your previous water supply pipes.
Your devices as well as product checklist need to make up the following:
Getting ready for the Installment
First of all, the sustaining frame provided with the bath must be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the taps device to prevent stress on the bath tub.
Fit the flexible tap adapters to the bottom of the two taps making use of 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you make use of every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath must currently prepare to be suited its final position.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installment, after that the first thing you should do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of removing the existing taps can be quite problematic due to the restricted gain access to that is typically the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the faucets. Have a fabric prepared for the staying water that will certainly originate from the pipelines. When the supply pipes have been eliminated, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning throughout this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any old sealing compound.
Prior to going on to fit the brand-new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Installing the Bathtub
Using both wood boards under its feet, put the tub in the required position. The wood boards are practical in uniformly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four small factors.
The following goal is to ensure that the bathtub is leveled all round. This can be attained by inspecting the spirit level and readjusting the feet on the tub up until the spirit level reviews degree.
To install faucets, fit all-time low of the furthest flexible faucet port to the suitable supply pipeline by making a compression sign up with; then do the same for the various other tap.
Switch on the water as well as check all joints and also new pipework for leaks and also tighten them if needed. Fill the bath tub and also examine the overflow outlet and also the typical outlet for leakages.
Lastly, fix the bathroom paneling as described in the maker's instruction manual. Tiling and also sealing around the bath tub must wait until the bath tub has been made use of at least when as this will resolve it into its last setting.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and also the other end gives a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin making certain that the washers remain in place in between the faucet and the sink. Safeguard the tap in place with the supplier offered backnut. When the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with regular tap ports. The previous kind needs to be connected to the tap finishes first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bath satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to split an inflexible seal, causing the water to penetrate the wall between the bathroom and also the tiling, leading to problems with moisture and also feasible leaks to the ceiling below.
You can select from a range of coloured sealers to assimilate your components and fittings. They are offered in tubes as well as cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly fill the bathtub with water before sealing, to allow for the motion experienced when the tub is in use. The sealant can split relatively very early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally conveniently readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water-proof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very eager about Installing A Bathtub and I hope you appreciated the blog entry. For those who enjoyed reading our article plz remember to pass it around. Thank you for going through it.
Book 24/7